石墨盤根填料環由石墨盤根或各種增強石墨盤根如，玻纖增強石墨盤根，不銹鋼絲增強石墨盤根，鎳絲增強石墨盤根INCONEL絲增強盤根由模具模壓成環，可用于填料函中上下端面的封口也可單獨成套使用，集合了盤根和普通石墨環的優點，特別適合于高溫高壓部位的密封。

　　石墨盤根填料環的安裝：

　　1.一次安裝一枚石墨盤根密封填料環，確信每根石墨盤根密封填料環沒有粘上塵土或其它碎片。如果需要應在石墨盤根密封填料環、軸或閥桿上涂上清潔潤滑油加以潤滑。多個石墨盤根密封填料環使用時要交錯安裝，每枚石墨盤根密封填料環的切口錯開90度。安裝環時應于軸向慢慢拉開，徑向的距離以能使石墨盤根密封填料環裝到軸上即可，使用填充工具緊固每根石墨盤根密封填料環。當足夠石墨盤根密封填料環安裝完成后，用隨動件將其封閉，使用隨動件可以增加緊密程度。隨動件只是做為一種補充，保證全部石墨盤根密封填料環適當的位置，避免石墨盤根密封填料環移動。

　　2.往復泵中，填料箱內的兩端和中間還應放入導向環，以保持其同心運動和受柱塞的重力。

　　3.安裝石墨盤根填料環后，扭緊螺栓。為了在每個螺母上施加一致的壓力，建議用力矩扳手或相關的計量裝置緊固螺母。請注意：此時裝置如果處于無泄漏狀態，可能引起石墨盤根密封填料環燃燒。建議開啟水泵后再慢慢扭緊螺栓直至漏量達到允許范圍。